厂商 ：深圳博瑞图电子科技有限公司
地址 ：广东 深圳主营产品 ：编程器 数据采集卡 仿真器 下载线 元器件配单
联系电话 ：13823138950
商品详情描述
Quickstart Card
This quickstart card applies only to the FlashPro4 device programmer.
Kit Contents
|
Quantity |
Description |
|
|
|
|
1 |
FlashPro4 programmer standalone unit |
|
|
|
|
1 |
USB A to mini-B USB cable |
|
|
|
|
1 |
FlashPro4 10-pin ribbon cable |
|
|
|
Software Installation
If you are already using Actel's Libero? Integrated Design Environment (IDE), you have the FlashPro software installed as part of Libero IDE. If you are using the FlashPro4 device programmer for standalone programming or on a dedicated machine, download and install the latest release of the FlashPro software from the Actel website. The installation will guide you through the setup. Complete the software installation before connecting the FlashPro4 device programmer to your PC.
Note: Libero IDE v8.6 SP1 or FlashPro v8.6 SP1 are the minimum versions required to run FlashPro4.
Software releases: www.actel.com/download/program_debug/flashpro.
Hardware Installation
After installing the software successfully, connect one end of the USB cable to the FlashPro4 device programmer and the other end to your PC’s USB port. The Found Hardware Wizard will open twice. Use the wizard to install the driver automatically (recommended). If the Found Hardware Wizard cannot find the drivers automatically, then ensure you have properly installed the FlashPro software prior to installing the hardware. If the drivers still cannot be installed automatically, then install them from a list or specific location (advanced).
If FlashPro was installed as part of the Libero IDE default installation, the drivers are located at C:/Libero/Designer/Drivers/Manual. For a standalone FlashPro default installation, the drivers are located at C:/Actel/FlashPro/Drivers/Manual. Actel recommends the automatic driver installation.
© 2010 Actel Corporation. All rights reserved.
FlashPro4 Device Programmer Quickstart Card
Note: FlashPro4 uses pin 4 of the JTAG connector whereas FlashPro3 had no connection to this pin. FlashPro4 pin 4 of the JTAG header is a PROG_MODE output drive signal. PROG_MODE toggles between programming and normal operation. The PROG_MODE signal is intended to drive an N or P Channel MOSFET to control the output of a voltage regulator between the programming voltage of 1.5 V and normal operation voltage of 1.2 V. This is required for ProASIC?3L, IGLOO? V2, and IGLOO PLUS V2 devices because, although they can operate at 1.2 V, they must be programmed with a VCC core voltage of 1.5 V. Please refer to FlashPro4 Backward Compatibility with FlashPro3 and Using FlashPro4 PROG_MODE for 1.5 V Programming of ProASIC3L, IGLOOV2, and IGLOO PLUS V2 Devices for more information.
|
TCK |
1 |
2 |
GND |
|
|
TDO |
|
3 |
4 |
PROG_MODE |
|
TMS |
|
5 |
6 |
VJTAG |
|
VPUMP |
|
7 |
8 |
TRST |
|
TDI |
9 |
10 |
GND |
|
|
|
|
|
|
|
Pin 4 on FlashPro4 programmers MUST NOT be connected or used for anything other than its intended purpose.
Common Issues
If the On LED does not light up after FlashPro4 driver installation, the driver might not be installed correctly and you must troubleshoot the installation. For more information, refer to the FlashPro Software and Hardware Installation Guide and the “Known Issues and Workarounds” section of the FlashPro software release notes: www.actel.com/download/program_debug/flashpro.
FlashPro4 may not operate correctly if pin 4 of the JTAG connector is improperly used. See the above note.
Documentation Resources
Refer to the FlashPro software page for further information:
www.actel.com/products/hardware/program_debug/flashpro.
Technical Support and Contacts
Technical support is available online at www.actel.com/support, by email at tech@actel.com, or by phone:
Phone (NA): 800.262.1060
Phone (Int'l): +1 650.318.4460
Actel Sales offices, including Representatives and Distributors, are located worldwide. To find your local representative go to: www.actel.com/company/contact.
***************************************************
联 系 人 ;雷 俊 （先 生）
深圳博瑞图电子科技有限公司
TEL:0755-36675904
MOB:13823138950
FAX:0755-83244576
ADD:深圳市福田区中航路世纪汇都会轩1416室
EMAIL: 401512450@qq.com
网 址：www.szprotools.com
***************************************************
承接销售元器件IC一条龙、专注10年
相关产品推荐
