供应QCA4004WIFI模块/串口wifi模块/无线透传wifi模组
GWF-KM01是一个功能齐全的WiFi模块,包括一些基于TCP的连接协议以及IP/启用SSL,通过
一个低成本、低功耗、低复杂度的系统获得的功能齐全的互联网连接和可靠的信息交换,
GWF-K1 WiFi连接是一个高度集成的、功能齐全、单频单流802.11n WiFi模块,包括一个高效
节能的板上功率放大器和低噪声放大器,是低系统成本优化,并最大限度地减少了所需的实
现可靠的WiFi链接。本模块主要是应用于远程控制、智能应用如云服务、智能插座、无线音
响、LED控制、可携带设备如iWatch、无线传感器节点等应用。
热线:13560725446 微信/QQ:478053711
2.4GHz
802.11 b/g/n 150Mbps
- 1. Scope:
GWF-KM01 is a full-featured WiFi module,including a number of TCP/IP-based connectivity protocols along with SSL,enabling a low-cost,low-complexity system to ontain full-featured internet connectivity and reliable information exchange.GWF-KM01 is a full-featured,single-band,single stream 802.11n solution.Including an energy efficient on-board power amplifier and low noise amplifier, low is cost optimization system, and minimizes the reliable WiFi links required. This module is mainly used in remote control, intelligent application of cloud service, intelligent socket, wireless audio, LED control, portable devices such as iWatch, wireless sensor nodes and other applications.
The GWF-KM01 module with pin design and half round design, in order to provide application pin output flexible and reliable, stable fixed design. The independent RF output design, requirements of design greatly simplifies the user, without the need for additional hardware technology in RF.
2、Product information
2.1 Block diagram
2.2 Outline information
As picture show: Pin1-pin33 is counterclockwise arrangement.
Length |
Mils(mm) |
A |
1417.3(36) |
B |
787.4(20) |
C |
47.992(1.219) |
D |
30.748(0.781) |
E |
157.52(4.001) |
3、Parameters and features:
Protocol and interface standard |
|
Web standards |
Wireless standards:IEEE 802.11a/b/g/n |
interface |
SPI,UART,SDIO,I2S&I2C,GPIO,USB |
RF parameters |
|
Operation Frequency |
ISM band , 2412~2483.5MHz (Depends on country region). |
Typical Transmit Power |
802.11b (CCK) 11Mbps: 9+/-1dBm |
|
802.11g (OFDM) 54Mbps: 8+/-1dBm |
|
802.11n (HT20@MCS7), 8+/-1dBm,(HT40@MCS15),7+/-1dBm |
Receive Sensitivity |
802.11b: -87+/-1dBm;802.11g: -70+/-1dBm, 802.11n (HT20), -65+/-1dBm;802.11n (HT40), -65+/-1dBm |
Features |
|
The working mode of WIFI |
Wireless network card (Client)/wireless access point (AP)/wireless Router,(Router) |
Wireless security support |
The wireless MAC address filtering |
64/128/152 - bit WEP encryption |
|
WPS, WPA-PSK、WPA2-PSK,WEP,TKIP |
|
Network management |
Remote WEB management |
The configuration file to import and export |
|
WEB software upgrade |
|
Other parameters |
|
Other properties |
Optional: spectrum bandwidth 20 MHZ, 40 MHZ, automatically |
Physical specifications |
|
Size |
36*20mm |
Weight |
2.5g |
4、Pin definition
Pin |
Function |
Direction |
Instructions |
1 |
GND |
GND |
GND |
2 |
VDDIO |
Power |
VDDIO_HOST |
3 |
TDO |
I/O |
TDO |
4 |
TCK/I2C_CLK |
I/O |
I2C_CLK |
5 |
UART1_TXD/I2SO_BCK/TM |
I/O |
UART1_TXD |
6 |
UART1_RXD/I2SO_MCK/TMS |
I/O |
UART1_RXD |
7 |
UART0_RXD/I2C_DATA/TDI |
I/O |
UART0_RXD |
8 |
SPI_CLK/I2S1_MCK |
I/O |
SPI_CLK/I2S1_MCK |
9 |
GND |
GND |
GND |
10 |
UART0_CTS |
I/O |
UART0_CTS |
11 |
UART0_RTS |
I/O |
UART0_RTS |
12 |
UART0_TXD |
I/O |
UART0_TXD |
13 |
VDD33 |
Power |
VDD33 |
14 |
SPI_MISO/SD_D0 |
I/O |
SPI_MISO/SD_D0 |
15 |
USB_DP |
I/O |
USB信号+ |
16 |
USB_DP |
I/O |
USB信号- |
17 |
SPI_INT/SD_D0 |
I/O |
SPI_INT/SD_D0 |
18 |
SD_D2/I2S1_SDI/HM0 |
I/O |
HM0 |
19 |
SPI_MOSI/SD_D3/I2S1_BCK |
I/O |
SPI_MOSI/I2S1_BCK |
20 |
SPI_CSn/SD_CMD/HM1 |
I/O |
HM1 |
21 |
CHIP_PWD# |
I |
Chip power_l control |
22 |
WAKEUP |
I/O |
WAKEUP Control |
23 |
GPIO16 |
I/O |
GPIO16 |
24 |
GPIO15 |
I/O |
GPIO15 |
25 |
GND |
GND |
GND |
26 |
DVDD_GPIO |
Power |
DVDD_GPIO |
27 |
GPIO17 |
I/O |
GPIO16 |
28 |
I2S0_WS/TRST |
I/O |
I2S0_WS/TRST |
29 |
GPIO18 |
I/O |
GPIO18 |
30 |
I2S0_SDI |
I/O |
Serial data input |
31 |
I2S0_SDO |
I/O |
Serial data output |
32 |
GND |
GND |
GND |
33 |
EXT_ANT |
I/O |
EXT_ANT |
5、 environment
5.1Temperature
5.1.1Operating Temperature
Continuous reliable operation in ambient temperature: -10?C to +50?C.
5.1.2Storage Temperature
The product is not damaged or degraded when keeping in -20?C to +85?C.
5.2Humidity
5.2.1 Operating Humidity Conditions
The product should be capable of continuous reliable operation when subjected to relativehumidity in the range of 20% to 80% (non-condensing) .
5.2.2Non-Operating Humidity Conditions (including warehouse)
The product should not be damaged or degraded when kept in the place (where relativehumidity range is in the range of 20% to 80%) for 36 hours.
6、Disclaimer
THESE MATERIALS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTYOF ANY KIND, EITHER EXPRESS OR IMPLIED , INCLUDING BUT NOT LIMITED TO, THEIMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSEOR NON-INFRINGEMENT.
We use reasonable efforts to include accurate and up-to-date information on this document; it does not, however, make any representations as to its accuracy or completeness of the information, text, graphics, links or other items contained within these materials. Your use of this Document is at your own risk. Ogemray, its suppliers, and other parties involved in creating and delivering this Document’s contents shall not be liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost profits.